Product overview

An acoustic louver creates the ideal acoustic barrier in ventilation apertures.

Lint filter boxes are designed to filter out lint.

Specially designed to reduce noise from ventilation outlets by being a combination of a jet hood and a sound attenuator.

VCR1 and VCC1 are manually operated control dampers specifically designed to regulate the airflow in ventilation systems.

Backflow dampers are designed to prevent backflow from Air Handling Units, which are equipped with backup fans.

The SAR3 model is specifically designed for ventilation systems, acting as both primary and secondary sound attenuators.

Circular sound attenuators are specially designed for use in ventilation systems to reduce sound from ventilation ducts.

Circular sound attenuators are specially designed for use in ventilation systems to reduce sound from ventilation ducts.

SOR1 and SOC1 are manually operated shut-off dampers designed to shut off the airflow in ventilation systems.

The Conex jet hood brings air up through the unit and mixes it with the atmosphere.

This circular 90° bend is part of the Simduct series and intended for use in duct systems.

This circular 60° bend is part of the Simduct series and intended for use in duct systems.

This circular 45° bend is part of the Simduct series and intended for use in duct systems.

This circular 30° degree bend is part of the Simduct series and intended for use in duct systems.

This circular 15° bend is part of the Simduct series and intended for use in duct systems.

The Class C ducts are part of the Simduct series and are the pipes in the duct system.

Implementors to the duct system for floor, wall and ceiling.

Intake hood that suctions air into the duct system. The intake hood is manufactured with wire mesh that prevents unwanted access.

The jet hood captures water in a funnel that would otherwise have entered the duct system. Prevents the duct system from filling with water.

Balancing damper for shutting off, adjusting, balancing or controlling the air flow.

Balancing damper for shutting off, adjusting, balancing or controlling the air flow.

The inspection hatch's primary application is to ensure easy access to the duct system for service, maintenance and inspection.

The inspection hatch's primary application is to ensure easy access to the duct system for service, maintenance and inspection.

This circular sound attenuator is part of the Simduct series and intended for use in duct systems. Circular sound attenuator with 50 mm insulation.

This circular sound attenuator is part of the Simduct series and intended for use in duct systems. Circular sound attenuator with 100mm insulation.

This circular equipment sleeve is part of the Simduct series and intended for use in duct systems.

This circular equipment nipple is part of the Simduct series and intended for use in duct systems.

Used at the exposed end of the duct system to protect against birds, animals and other intruders.

Circular end base that is part of the Simduct series and intended for use in duct systems. Used to shut off duct openings.

This circular joint nipple is part of the Simduct series and intended for use in duct systems.

Circular extension sleeve is part of the Simduct series and intended for use in duct systems. Use to join the parts together.

This circular T-piece is part of the Simduct series and intended for use in duct systems.

This circular centric transition is part of the Simduct series and intended for use in duct systems.

This circular eccentric transition is part of the Simduct series and intended for use in duct systems.

Oblong simple control rack that makes service and maintenance significantly more cost effective.

The transition is Class A and is designed and prepared for use in HVAC systems.

Angled leaves that allow light and air to pass through while blocking rain, direct sunlight and noise.

The sound attenuator reduces noise flowing through ventilation openings in offshore and onshore ventilation systems.

The suspension bar can be supplied in all material qualities and is designed and prepared for use in HVAC systems.

The class A circular jet cap is designed and prepared for use in duct systems.

The inspection hatch's primary application is HVAC systems. Used for inspection of duct systems.

Flexible system for both circular and rectangular duct systems. Fits perfectly on most duct systems.

The class A circular T-piece is designed and prepared for use in HVAC systems.

The class A circular swan neck is designed and prepared for use in duct systems and ventilation systems.

The class A rectangular special duct is designed and prepared for use in HVAC systems.

The class A circular transition is designed and prepared for use in HVAC systems.

The class A circular flange is designed and prepared for use in HVAC systems.

The Class A rectangular flange is designed and prepared for use in HVAC systems.

The class A special bend is designed and prepared for use in HVAC systems.

The grate has a steel frame around it. Manufactured according to ISO 15138, or otherwise on request.

The log is used for both supply and discharge air. Available in several types and dimensions.

The Class A rectangular implementation is designed and prepared for use in wall and deck applications in connection with HVAC systems

The special bend is available in several types and dimensions.

The damper is equipped with GRP cross-tubes and lifting hooks as standard.

The right duct is Class A and is designed and prepared for use in HVAC systems.

The class A rectangular special bend is designed and prepared for use in HVAC systems.

The Class A rectangular bend is designed and prepared for use in HVAC systems.

Correct Class A duct for use in HVAC systems.